waveshare 5.65inch E-Ink Display HAT 7-Color ACeP E-Paper Display 600x448 Pixels for Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W/Zero WH and Jetson Nano 5.65inch-Seven Colors

BE SAFE

WE ONLY SOURCE

FROM OFFICIAL SUPPLIERS

From United States

To International

In 5-10 Days

US$19.99 Shipping Fees for any Order

GRAND SELECTION

Think of it and most probably we have it among our grand selection of products!

AMAZING PRICES

Get ready for the amazing and best Supps prices ever!

FIXED RATE DELIVERY

Get your order anywhere on this planet within 5-10 days with a fixed rate of $19.99 (no matter the size of your order)

+1 (844)-467 8777

PHONE:

+1 (844)-467 8777

waveshare 5.65inch E-Ink Display HAT 7-Color ACeP E-Paper Display 600x448 Pixels for Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W/Zero WH and Jetson Nano 5.65inch-Seven Colors

Regular Price: US$125.99

Special Price US$104.99

Availability: In stock

Supplier: waveshare

Category: Electronics Computers & Accessories Monitors

Qty:

Frequently bought together :

Price for all selected :

US$154.98

Overview 5.65inch 7-Color e-Paper Module: low power consumption, wide viewing angle, paper-like displaying without electricity Specifications Operating voltage: 3.3V/5V Display color : ACeP 7-Color Resolution: 600 × 448 pixels Interface: 3-wire SPI, 4-wire SPI Grey scale : 2 Full refresh time: <35s Refresh power : 50mW (typ.) Dot pitch: 0.1915 × 0.1915mm Standby current: <0.01uA (almost none) Viewing angle: >170° Display size: 114.9 x 85.8mm Outline dimensions : 138.5 x100.5mm SPI control interface---supports control boards including Raspberry Pi/Jetson Nano/Arduino/STM32. VCC---3.3V/5V GND---Ground DIN ---SPI MOSI pin CLK---SPI SCK pin CS---SPI chip selection, low active DC---Data / Command selection (high for data, low for command) RST---External reset, low active BUSY---Busy status output Application Suitable for price Tags, asset/equipment Tags, shelf labels, conference name tags... Online Resource/Online user manual ://bit.ly/3YPykk9 Precautions 1. For E-paper displays that support partial refresh, please note that you cannot refresh them with the partial refresh mode all the time. After refreshing partially several times, you need to fully refresh EPD once. Otherwise, the display effect will be abnormal, which cannot be repaired! 2. Note that the screen cannot be powered on for a long time. When the screen is not refreshed, please set the screen to sleep mode or power off it. Otherwise, the screen will remain in a high voltage state for a long time, which will damage the e-Paper and cannot be repaired! Package Content 5.65inch e-Paper Module (F) x1 PH2.0 20cm

Note: The FPC cable of the screen is fragile. Do not bend the cable along the vertical direction of the screen to avoid tearing the cable. Do not repeatedly excessive bending line, to avoid line fracture. Do not bend the cable toward the front of the screen to prevent the cable from being disconnected from the panel. It is recommended to use fixed wiring during debugging and development. Suitable for price Tags, asset/equipment Tags, shelf labels, conference name tags, etc. SPI control interface: Compatible with Raspberry Pi/Jetson Nano/withArduino/STM32. Multiple voltage level support: Onboard voltage translator, compatible with 3.3V / 5V MCUs. 5.65inch Colorful 7-Color e-Paper E-Ink Display Module, 600×448 pixels, Advanced Color ePaper (ACeP) technology, supports 7-Color display.Low power consumption, wide viewing angle, paper-like displaying without electricity.