Taidacent UAF42 Universal Active Filter Module High Pass Low Pass Band Pass Filtering Active Band Pass Filter Module Tunable Filter

BE SAFE

WE ONLY SOURCE

FROM OFFICIAL SUPPLIERS

From United States

To International

In 5-10 Days

US$19.99 Shipping Fees for any Order

GRAND SELECTION

Think of it and most probably we have it among our grand selection of products!

AMAZING PRICES

Get ready for the amazing and best Supps prices ever!

FIXED RATE DELIVERY

Get your order anywhere on this planet within 5-10 days with a fixed rate of $19.99 (no matter the size of your order)

+1 (844)-467 8777

PHONE:

+1 (844)-467 8777

Taidacent UAF42 Universal Active Filter Module High Pass Low Pass Band Pass Filtering Active Band Pass Filter Module Tunable Filter

Regular Price: US$89.99

Special Price US$74.99

Availability: In stock

Supplier: Taidacent

Category: Electronics Accessories & Supplies Power Strips & Surge Protectors Power Strips

Qty:

UAF42 is a universal active filter that can be configured for various low-pass, high-pass, and band-pass filters. It uses a classic state-variable analog architecture with an inverting amplifier and two integrators. The integrator includes an on-chip 1000pF capacitor trimmed to 0.5%. Many filter types can be easily implemented, such as Butterworth, Bessel and Chebyshev. A fourth useless FET input operational amplifier (same as the other three) can be used to form additional stages, or for special filters such as band stop and inverse Chebyshev. Generally used in power system, sensor signal processing, transmitter and receiver, signal generator processing, etc.

Parameter

Module model	UAF42
Module type	universal adjustable filter
Module supply voltage	±5V-±15V
Module power supply current	10mA (Max)
Module control mode	potentiometer
Filter type	high-pass, low-pass, band-pass; the center frequency can be customized according to customer requirements
Low-pass cut-off fre range	100KHz (MAX); the default potentiometer cut-off frequency range is within 5K; the maximum cut-off frequency is not supported, users need to replace the RF1 and RF2 potentiometers according to their own needs
Qualcomm cut-off fre range	30KHz (MAX); the default potentiometer cut-off frequency range is within 2K; the maximum cut-off frequency is not supported, users need to replace RF1 and RF2 potentiometers according to their own needs
Bandpass center fre range	50Hz-40KHz; the default potentiometer cut-off frequency range is within 500Hz-5KHZ; the minimum and maximum center frequencies are not supported, users need to replace the RF1 and RF2 potentiometers according to their own needs
Input signal form	single-ended; default VIN2 input
Input signal voltage range	less than positive and negative power supply
Input frequency range	DC-1MHz
Module gain range	40dB (MAX)
Q value adjustable range	20 (MAX)
Input output characteristics	DC input and output; output with DC component, please add DC blocker to the radio frequency equipment, or directly use oscilloscope
Module protection	none; no reverse connection protection, unlimited current protection

Module features: multi-function filter, universal adjustable filter

Module application: power system, sensor signal processing, transmitter and receiver, signal generator

Module specifications: 50*50*15mm; length*width*height-PCB size

Module weight: 20.6g

Module working temperature: 0-75?; civil grade

Interface description

Precautions for module use

(1) The module power supply is a positive and negative dual power supply, and the voltage cannot exceed positive and negative 18V.

(2) Since the module is a high-precision device, in order to avoid unnecessary interference, it is recommended to use a linear power supply.

(3) For the output signal, it is recommended to use the SMA to BNC line to input and output signals. Use an oscilloscope to observe the effect. Poor contact or poor quality wires may cause signal attenuation or excessive noise.

(4) The filter measurement generally adopts the oscilloscope point frequency method. If possible, you can use a frequency sweeper or a vector network analyzer to test. Please add a DC block.

Size diagram

FAQ

Q: There is no problem when the module first got the output. After adjusting the potentiometer, now there is no input signal, there will be output signal. How to get it?

A: From the perspective of the phenomenon, it should be over-adjusted. The module is self-excited. You need to turn RF1 and RF2 clockwise a few more turns at the same time. The RQ potentiometer can be turned counterclockwise a few turns. Reduce the center frequency and Q value. Will be self-excited.

Q: Can UAF42 adjust the bandpass from 20HZ to 20KHz?

A: No, UAF42 can only be adjusted to a narrowband filter, such as 1K center frequency 100hz bandwidth, if a wideband filter is needed, we have a custom fourth-order filter to do it.

Q: The input signal of the module is 1Vpp, the output signal is too large, and how to adjust the unevenness in the band 2

A: If you don't need to amplify, just use the channel 1 output. The gain can be controlled by the RG potentiometer. The unevenness in the band is generally that the Q value is too high. Adjust the Q value counterclockwise to reduce the in-band fluctuation.

UAF42 test chart


UAF42 high pass test curve Cut-off frequency: 10Hz--30KHz (MAX)	UAF42 low pass test curve Cut-off frequency: DC--40KHz (MAX)	UAF42 bandpass test curve Center frequency: 1Hz--35KHz (MAX)

Generally used in power system, sensor signal processing, transmitter and receiver, signal generator processing, etc. A fourth useless FET input operational amplifier (same as the other three) can be used to form additional stages, or for special filters such as band stop and inverse Chebyshev. The integrator includes an on-chip 1000pF capacitor trimmed to 0.5%. It uses a classic state-variable analog architecture with an inverting amplifier and two integrators. UAF42 is a universal active filter that can be configured for various low-pass, high-pass, and band-pass filters.