Sound Storm Laboratories CG1501M Monoblock Car Amplifier - 1500 Watts 2/4 Ohm Stable Class A/B Mosfet Power Supply Great for Car Subwoofers Monoblock Class A/B 1500W

BE SAFE

WE ONLY SOURCE

FROM OFFICIAL SUPPLIERS

From United States

To International

In 5-10 Days

US$19.99 Shipping Fees for any Order

GRAND SELECTION

Think of it and most probably we have it among our grand selection of products!

AMAZING PRICES

Get ready for the amazing and best Supps prices ever!

FIXED RATE DELIVERY

Get your order anywhere on this planet within 5-10 days with a fixed rate of $19.99 (no matter the size of your order)

+1 (844)-467 8777

PHONE:

+1 (844)-467 8777

Sound Storm Laboratories CG1501M Monoblock Car Amplifier - 1500 Watts 2/4 Ohm Stable Class A/B Mosfet Power Supply Great for Car Subwoofers Monoblock Class A/B 1500W

Regular Price: US$173.99

Special Price US$144.99

Availability: In stock

Supplier: Sound Storm Laboratories

Category: Automotive Car & Vehicle Electronics Car Electronics Car Audio Amplifiers Dual-Channel Amplifiers

Qty:

Tweak your vehicle's Bass with the Sound Storm Laboratories “Charge” series CG1501M class A/B Monoblock Amplifier.

With 1500 Watts Max Power and MOSFET power supply, this amplifier offers high performance with more Bass for your subwoofers.

Customize the sound with variable low pass crossover, switchable Bass Boost, crossover switch, and remote subwoofer control. The Charge series offers eye-catching aesthetics and customization for an outstanding entertainment experience.

Class A/B, Monoblock, MOSFET power supply
1500 Watts @2-Ohms x 1 Max, 750 Watts @4-Ohms x 1 Max
High and low level inputs, Thermal overload speaker and short protection
Power and protection LEDs, Variable low pass crossover, Switchable bass boost
Variable input gain control, Input sensitivity selector, RCA line level inputs
THD @ RMS output: 0.01%, S/N Ratio: 105 dB, Frequency: 9 Hz – 50 KHz
Dimensions: 11.72” x 6.5” x 2.40”, Weight: 8.1 lbs.
Remote Subwoofer Control


MOSFET Power Supply Metal Oxide Semiconductor Field-Effect Transistors quickly switch from full to non-conduction for high-efficiency output.	Class A/B Our Class-A/B amplifiers feature specific linear circuitry that increases sound quality and power output while reducing distortion and improving efficiency.	2 Ohm Stable 2-Ohm stable comfortably powers speakers or subwoofers when in use at 2-Ohms, resulting in more power and volume.	High and Low Level Inputs High-level inputs accept speaker output signals and low-level inputs accept pre-amp output signals to allow for the addition of amps and processors to standard factory or aftermarket source units.


Variable Low Pass Filter Variable low-pass filter gives you control over the frequencies that pass through to the subwoofer.	Switchable Bass Boost Switchable Bass Boost allows you to boost the low bass +18db.	Short Protection Automatic shut-off protects the amplifier if it gets too hot or if speakers fail causing a short.	Variable Input Control The Variable Input Control allows the amplifier input to match the output signal from the head unit to achieve optimum performance when adjusted properly.

Power Input Terminals

When installing all Sound Storm Laboratories amplifiers, it is important to use the MAXIMUM gauge of wire that the power terminals will accommodate. For instance, if an amplifier has 4 gauge power and ground terminals, use high quality 4 gauge multi-strand copper wire to make your power connections. This maximizes the amplifier’s ability to draw the required power upon demand. This also helps prevent overheating that could cause failure. ALWAYS make sure your vehicle’s electrical system is capable of handling the current demands from any after-market accessory.

Please refer to the amplifier’s owner’s manual for correct wire gauge sizes.

Fuses

Fuses protect BOTH the amplifier and the electrical system of your vehicle from faulty conditions.

If you must replace a fuse on the amplifier, always use a fuse of exactly the same type and rating of the one you are replacing. A different type of fuse or rating may result in damage or cause a fire. Please refer to your owner’s manual for reference on fuse size and type.

If you plan on using multiple amplifiers in your system, be certain that you have the appropriately sized gauge wire to accommodate the current demands for all amplifiers and that the wire is fused correctly at the battery. Connect an empty fuse holder within 18" (45 cm) of the car battery and run a 4 gauge (or heavier) cable from this fuse to the amplifier location. A fused distribution block is recommended when using several amplifiers or accessories.

Proper Grounding

Proper grounding is essential for any electric accessory in a vehicle.

Some key points to remember: Keep the ground as short as possible. Connect the amplifier’s power ground terminal to the closest point on the chassis of the car. Keep this ground wire to less than 39" (100 cm) in length. Use 4 gauge (or heavier) wire. Scrape any paint away, use a star washer to “bite” into the metal and secure it tightly using a grounding lug.

Any steps that aren’t followed properly will result in a higher resistance at the ground point, causing unnecessary heat, high current draw, and potentially damaging the electrical accessories in the vehicle.

Installation

Please be advised that “Professional” installation of all of our products is recommended and encouraged.

Sound Storm Laboratories CG1501M Monoblock Car Amplifier - 1500 Watts 2/4 Ohm Stable Class A/B Mosfet Power Supply Great for Car Subwoofers

Warranty - Sound Storm Laboratories provides a powerful 6-year Platinum Online Dealer warranty so long as the purchase is made through We strongly encourage professional installation of this product to ensure proper and safe functionality. Specs - Dimensions 11 72” x 6 5” x 2 5” Weight 5 2 lbs. Low & High Level Inputs - A low level (RCA) input is measured in voltages A high level (+/- wire) input is measured in wattages Both essentially carry signal from your receiver to your amplifier to your speakers. Variable Gain Control - The gain control is not for adjusting volume It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier. Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it. Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies You can set exact sound specifications for the bass frequency reproduction. Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current It controls the output voltage & current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry. Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal. Power - 1500 Watts Max x 1 @2-Ohms 750 Watts Max x 1 @4-Ohms.