LILYGO T-Display-S3 ESP32-S3 1.9-inch ST7789 LCD Display Touchable Screen Development Board TTGO Wireless Module Touch-screen version

BE SAFE

WE ONLY SOURCE

FROM OFFICIAL SUPPLIERS

From United States

To International

In 5-10 Days

US$19.99 Shipping Fees for any Order

GRAND SELECTION

Think of it and most probably we have it among our grand selection of products!

AMAZING PRICES

Get ready for the amazing and best Supps prices ever!

FIXED RATE DELIVERY

Get your order anywhere on this planet within 5-10 days with a fixed rate of $19.99 (no matter the size of your order)

+1 (844)-467 8777

PHONE:

+1 (844)-467 8777

LILYGO T-Display-S3 ESP32-S3 1.9-inch ST7789 LCD Display Touchable Screen Development Board TTGO Wireless Module Touch-screen version

Regular Price: US$71.99

Special Price US$59.99

Availability: In stock

Supplier: LILYGO

Category: Electronics Computers & Accessories Computer Components Single Board Computers

Qty:

Frequently bought together :

Price for all selected :

US$104.98

T-Display-S3 Specifications

T-Display-S3 is a ESP32-S3 development board.
It is equipped with a color 1.9" LCD screen and two programmable buttons.
Communication using I8080 interface. Retains the same layout design as T-Display.
You can directly use ESP32S3 for USB communication or programming.
more product programming information Please refer to Github :github.com/Xinyuan-LilyGO/T-Display-S3

Instructions for use:

Firstly, upload the program (github. com/Xinyuan LilyGO/T Display S3)

2. The board uses USB as the JTAG upload port.

When printing serial port information on USB_CDC_ON_BOOT configuration needs to be turned on.

If the port cannot be found when uploading the program or the USB has been used for other functions, the port does not appear.

Please enter the upload mode manually.

Connect the board via the USB cable
Press and hold the BOOT button , While still pressing the BOOT button, press RST
Release the RST
Release the BOOT button
Upload sketch

Product Pin Diagram

NOTE:

The program can be written normally, but there is still no display after writing.

There are factory test files in the firmware folder, which can be flashed into the board to check whether the board is normal.

If there is still no display, then it can be judged that there is a problem with the board or the screen.

Delete the ( TFT_eSPI ) in the libraries, and replace the ( TFT_eSPI ) in the folder of the main page to the libraries directory
When opening the Arduino IDE, it prompts whether to upgrade the library, please choose not to upgrade, otherwise it will overwrite the configuration of the ( TFT_eSPI ) display

2. The factory sample program includes steps for connecting to WiFI

Due to the need to increase the power of the chip when searching for WiFi signals, it is normal for the chip to generate heat

When you connect to WiFi or after the program runs, the search will stop and the normal operating temperature will be restored

Shipping List

1 X T-Display-S3 Touch Version
1 X 2.54mm Male PIN (1*12P)
1 X JST 1.25mm 2P

Solder pin version

More information

USB	USB2.0 (USB A-USB C) cable
Drive Chip	ST7789V
Github	github.com/Xinyuan-LilyGO/T-Display-S3
Product introduction	youtube.com/watch?v=88MwR-4Dy0Q
Solder pin version	amazon.com/dp/B0CP8W1BN8?ref=myi_title_dp

?Product service?: If you have any questions or suggestions about the product, please feel free to contact us. We will answer your question as soon as possible. ?Github? :github.com/Xinyuan-LilyGO/T-Display-S3. ?Programming?:You can directly use ESP32S3 for USB communication or programming. ?Features?: It is equipped with two programmable button. ?Screen?: 1.9-inch ST7789 LCD Display Touch screen.