IPCamPower POE Combiner Splitter Adapter Run 2 IP Cameras on 1 Cable Works on All POE Switches POE NVR and POE Cameras Mode A and B POE Compatible

BE SAFE

WE ONLY SOURCE

FROM OFFICIAL SUPPLIERS

From United States

To International

In 5-10 Days

US$19.99 Shipping Fees for any Order

GRAND SELECTION

Think of it and most probably we have it among our grand selection of products!

AMAZING PRICES

Get ready for the amazing and best Supps prices ever!

FIXED RATE DELIVERY

Get your order anywhere on this planet within 5-10 days with a fixed rate of $19.99 (no matter the size of your order)

+1 (844)-467 8777

PHONE:

+1 (844)-467 8777

IPCamPower POE Combiner Splitter Adapter Run 2 IP Cameras on 1 Cable Works on All POE Switches POE NVR and POE Cameras Mode A and B POE Compatible

Regular Price: US$41.99

Special Price US$34.99

Availability: In stock

Supplier: IPCamPower

Category: Electronics Computers & Accessories Networking Products Network Adapters Powerline Network Adapters

Qty:

Frequently bought together :

Price for all selected :

US$74.98

IPCamPower's POE Combiner and Splitter. A must have for all IP Camera Installers.

Setup is Easy!


Simply Plug the Combiner Unit into a POE Switch or POE NVR This works on any standard POE Switch or POE NVR. Simply plug it in with no IP configuration needed. Your switch or NVR will "think" you are using 2 cables.	This combines the 2 ports of POE and Data into 1 cable. The special Combiner unit then takes the 2 cables from the POE switch or POE NVR and combines the data and POE power into one cable. You entire cable run between the POE Switch/NVR and Cameras should not exceed the standard 330' allowable by a standard network run.	Then at the camera end, the splitter will split out the POE and Data into 2 shorter cables. The splitter unit will be installed near your cameras and it takes the combined POE power and Data and splits it back out to 2 cables again.	The finished product is simple and effective. The finished product is a simple yet effective solution that will save you time and money in your next IP Camera installation.

Toggle switch allows for all NVRs and Switches

A Typical IP Camera Installation using a single Cable for all Cameras.

With a typical IP Camera installation, you would make a home run cable run from the POE Switch or NVR to each camera. While this is still recommended for alot of applications, what if you had areas in which you had 2 cameras side by side? Wouldn't it be nice if you could run one cable to manage both of these cameras?

A camera installation using IPCamPower's IP Camera Splitter and Combiner

An IP Camera Installation using IPCamPower's POE Combiners and Splitters

Using IPCamPower's POE Combiners and Splitters, you significantly reduce cable and labor costs by just running one long cable to the areas in which you have 2 cameras side by side.

Simple plug n play installation. Works with all standard 802.3af/at POE switches. Also works on POE NVRs due to the new updated design with the onboard toggle switch. If your switch or NVR uses standard POE power, this unit will work!. The Receiver Unit comes with weatherproof RJ45 connectors, allowing you to fully expose the Receiver unit to the weather elements. Ever installed a camera in a location, only to find out that you need another one right by it? Whats worse, the switch is on the other side of the building and it took you hours to run that one cable run. No worries! Just use this splitter set to make your installation much easier as all you need to do now is run 1 cable from the old camera to the new camera. Reduces cabling costs. Lets say you are installing 2 cameras on each side of a corner. Instead of running 2 cables back to the switch, you can now just run 1. Easy and Cost Effective. Allows you to run 1 cable run to the switch for 2 cameras that are near each other. Set consists of a "sender" unit and a "receiver" unit. Plug Sender unit into 2 open ports on your POE switch. Run one cable to the location that has the cameras that are nearby each other. Connect 2 short cables to the Receiver unit and connect the other ends to your camera. Done!.