Geekworm X1001 PCIe M.2 Key-M NVMe SSD PIP PCIe Peripheral Board for Raspberry Pi 5

BE SAFE

WE ONLY SOURCE

FROM OFFICIAL SUPPLIERS

From United States

To International

In 5-10 Days

US$19.99 Shipping Fees for any Order

GRAND SELECTION

Think of it and most probably we have it among our grand selection of products!

AMAZING PRICES

Get ready for the amazing and best Supps prices ever!

FIXED RATE DELIVERY

Get your order anywhere on this planet within 5-10 days with a fixed rate of $19.99 (no matter the size of your order)

+1 (844)-467 8777

PHONE:

+1 (844)-467 8777

Geekworm X1001 PCIe M.2 Key-M NVMe SSD PIP PCIe Peripheral Board for Raspberry Pi 5

Regular Price: US$35.99

Special Price US$29.99

Availability: In stock

Supplier: Geekworm

Category: Electronics Computers & Accessories Computer Components Single Board Computers

Qty:

READ ME before Starting

Enable PCIe: Must make sure to enable PCIe in the OS on the NVME SSD you are booting, instead of the OS on SD card. Too many people just enable PCIe in the OS on the SD CARD.
Update eeprom firmware: Check and upgrade the bootloader firmware to the latest version;
Set NVME boot order;
DON'T enable PCIe 3.0, ONLY PCIe 2.0 is supported by Raspberry Pi fundation.
If your SSD is old and has a DOS partition, delete the DOS partition and repartition the SSD (feedback from buyer)
Please refer to the guide on Geekworm Wiki for specific operations.

[PS]: The official Raspberry Pi firmware is frequently upgraded and the OS is not stable enough. It is also a challenge for us.

Note: The Raspberry Pi 5, M.2 NVME SSD, power supply is not included in the packing list.

Overview

The X1001 V1.1 shield is an NVME M2 SSD PIP (PCIe Peripheral Board) for the Raspberry Pi 5 that uses the new PCIE interface of the Raspberry Pi 5 to utilise the NVME M2 SSD for fast data transfers and ultra-fast booting.

User Manual: wiki.geekworm.com/X1001

Features

Minimalist design, easy to install.
FFC cable is only 30mm length.
Compatible with other HAT shield;
Supports installation of official Pi 5 active cooler;
Dual LED Indicators:PCE: PCie - The LED will be on if the SSD is recognised; ACT - M.2 disk activity (“ACT”).
Supports 2230/2242/2260/2280 NVME M2 ssd.
Can Power the X1001 shield directly from the FPC PCIe ribbon (providing maximum 5W of continuous power)
Integrated with XH2.54 5V power connector, just use it if you are using a ultra large capacity SSD if the current is not enough.

PS:

Maximum current for PCIe wire is 1A, and voltage is 5V.
If you find that the SSD is not working properly, it is possible that the power supply of SSD is not enough, then you need to check the current requirement of your SSD to decide whether power the SSD separately.
The X1001 hardware has no limit on NVME SSD capacity, which is dependent on the Raspberry Pi OS.

How to Power

Can power the X1001 shield directly from the FFC PCIe ribbon (providing maximum 5W of continuous power)

Packing List

1 x X1001 V1.1 NVMe SSD Shield
1 x PCIe FFC cable(30mm length)
3 x M2.5x17mm F/F Spacers
6 x M2.5x5mm Screws
1 x M2x4mm Screws (to fix MVME M2 SSD)


	X1000	X1001	X1002
Compatible with	Raspberry Pi 5	Raspberry Pi 5	Raspberry Pi 5
Mounting Position	Top	Top	Bottom
M.2 NVMe SSD	2230/2242	2230/2242/2260/2280	2230/2242/2260/2280
Matching Case	P579(ASIN:B0CRD7XQCK)	P579(ASIN:B0CRD7XQCK)	Will release soon

?Updated Version?With just one ACT led. ?User Manual?Refer to Geekworm WiKi and search X1001. ?Packing List?1 x X1001 PCIe Peripheral Board, 1x Accessories Pack (Note: not include Raspberry Pi 5, SSD, TF card or power adapter.). ?How to Power?Power the X1001 shield directly from the FFC PCIe ribbon. Recommend to use Geekworm PD 27W power adapter (:B0CP7WPZZY ). ?M2 SSD Supported?Support M.2 KEY-M NVMe SSD 2230/2242/2260/2280 length installation. (Do not reserve the nut column to fix the 2230/2242/2260 SSD.). ?Compatibility?Raspberry Pi 5 PCIe HAT only compatible with Raspberry Pi 5 8GB / 4GB / 2GB / 1GB computer (NOT include Raspberry Pi 5).