Geekstory BN-220 Dual GPS Glonass Module Navigation TTL Level 9600bps + GPS Passive Antenna for Arduino Raspberry Pi Pixhawk F3 CC3D Betaflight F4 Flight Control

BE SAFE

WE ONLY SOURCE

FROM OFFICIAL SUPPLIERS

From United States

To International

In 5-10 Days

US$19.99 Shipping Fees for any Order

GRAND SELECTION

Think of it and most probably we have it among our grand selection of products!

AMAZING PRICES

Get ready for the amazing and best Supps prices ever!

FIXED RATE DELIVERY

Get your order anywhere on this planet within 5-10 days with a fixed rate of $19.99 (no matter the size of your order)

+1 (844)-467 8777

PHONE:

+1 (844)-467 8777

Geekstory BN-220 Dual GPS Glonass Module Navigation TTL Level 9600bps + GPS Passive Antenna for Arduino Raspberry Pi Pixhawk F3 CC3D Betaflight F4 Flight Control

Regular Price: US$47.99

Special Price US$39.99

Availability: In stock

Supplier: Geekstory

Category: Electronics GPS & Finders & Accessories GPS System Accessories Antennas

Qty:

Specification

Receiving Format : GPS,GLONASS,Galileo,BeiDou,QZSS and SBAS

Frequency : GPS L1,GLONASS L1,BeiDou B1,SBAS L1,Galileo E1

Channels : 72 Searching Channel

Sensitivity

Tracking : -167dBm, Reacquisition : -160dBm

Cold start : -148dBm, Hot start : -156dBm

Accuracy

Position Horizontal : 2.0 m CEP 2D RMS SBAS Enable (Typical Open Sky)

Velocity : 0.1m/sec 95% (SA off)

Timing : 1us synchronized to GPS time

Acquisition Time

Cold Start : 26s, Warm start : 25s, Hot start : 1s

Data and Update Rate

Support Rate : 4800bps to 921600bps,Default 9600bps

Data Level : TTL or RS-232,Default TTL level

Data Protocol : NMEA-0183 or UBX, Default NMEA-0183 Single GNSS : 1Hz-18Hz

Concurrent GNSS : 1Hz-10Hz,Default 1Hz

Operational Limits

Altitude : 50,000m Max, Velocity : 515m/s Max, Acceleration : Less than 4g

Power consumption

VCC : DC Voltage 3.0V-5.5V,Typical: 5.0V

Current : Capture 50mA/5.0V

Operating temp : -40 °C to +85°C

Storage Temp : -40°C to +105°C

Indicator:

TX LED:blue.The data output, TX LED flashing

PPS LED:red.PPS LED not bright when GPS not fixed,flashing when fixed

Wiring:

GND,TX output,RX input,VCC(3.0v-5.5v)

NMEA message output sample

GNRMC,073114.00,A,2237.56240,N,11401.59614,E,1.329,21.11,020916,,,A,V*37

GNVTG,21.11,T,,M,1.329,N,2.462,K,A*1B

GNGGA,073114.00,2237.56240,N,11401.59614,E,1,12,0.78,112.9,M,-2.5,M,,*54

GNGSA,A,3,19,05,02,06,17,12,09,13,,,,,1.48,0.78,1.26,1*01

GNGSA,A,3,69,83,84,70,68,82,,,,,,,1.48,0.78,1.26,2*0E

GPGSV,4,1,13,02,46,340,36,05,52,254,37,06,42,041,41,09,22,053,40,0*6E

GPGSV,4,2,13,12,32,282,35,13,13,185,33,17,36,131,37,19,57,119,44,0*66

GPGSV,4,3,13,20,03,237,,23,00,038,,25,09,311,19,42,51,128,32,0*60

GPGSV,4,4,13,50,46,123,33,0*50

GLGSV,2,1,08,68,25,027,39,69,78,011,36,70,40,213,43,74,00,259,,0*78

GLGSV,2,2,08,82,06,124,36,83,46,085,44,84,44,358,41,85,05,324,14,0*74

GNGLL,2237.56240,N,11401.59614,E,073114.00,A,A*7C


BN 220 GPS connection to flight controller VCC to 5V RX to TX3 TX to RX3 GND to GND	betaflight Software Set up GPS module with betaflight Software	BN 220 GPS connection to sensor VCC to 5V RX to D4 TX to D3 GND to GND


	BN-180 GPS	BN-220 GPS	BN-800 GPS	BN-880 GPS
Flash	No	4M Flash	4M Flash	4M Flash
Compass	No	No	HMC5883L	HMC5883L
Antenna Type	Passive	Passive	Passive	Active
Defaut Working Mode	GPS+GLONASS	GPS+GLONASS	GPS+GLONASS	GPS+GLONASS
Voltage	3.6-5.5V	3.6-5.5V	3.6-5.5V	3.6-5.5V
Default Baudrate	9600	9600	9600	9600
Frequency Range	1-10HZ	1-10HZ	1-10HZ	1-10HZ
Output	TTL	TTL	TTL	TTL
Pin Header	GND,TX,RX,VCC	GND,TX,RX,VCC	SDA,GND,TX,RX,VCC,SCL	SDA,GND,TX,RX,VCC,SCL
Connector	1.0mm pitch 4P	1.0mm pitch 4P	1.25mm pitch 6P	1.25mm pitch 6P

GPS Modules Comparison

BN-180 GPS Module Size: 18*18*6mm

BN-220 GPS Module Size: 22*20*6mm

BN-880 GPS Module Size: 28*28*10mm

BN-800 GPS Module Size: 35*35*6mm

BN 220 gps module documentation link cannot be displayed. If you need technical documentation, please click “Ask a question” to em-ail us. Data Level : TTL or RS-232,Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable. The TX LED flash means gps module output normally.The PPS LED flash means gps module locate your place. When you use it for Raspberry Pi, there is no driver needed but you need to install software. BN-220 gps module has flash to save configuration, so you do not need to reset data next time when you use it. But it has no compass. If you need gps with flash and compass, please buy bn-880 from Geekstory.