AURSINC SHARI PiHat - Portable SA818 Ham Allstar Radio Interface Compatible with Raspberry Pi 2/3/4 | Raspberry Pi Hosted Allstar Node | UHF Frequency Range 1W 420-450MHz/70cm | Amateur Radio Operator

BE SAFE

WE ONLY SOURCE

FROM OFFICIAL SUPPLIERS

From United States

To International

In 5-10 Days

US$19.99 Shipping Fees for any Order

GRAND SELECTION

Think of it and most probably we have it among our grand selection of products!

AMAZING PRICES

Get ready for the amazing and best Supps prices ever!

FIXED RATE DELIVERY

Get your order anywhere on this planet within 5-10 days with a fixed rate of $19.99 (no matter the size of your order)

+1 (844)-467 8777

PHONE:

+1 (844)-467 8777

AURSINC SHARI PiHat - Portable SA818 Ham Allstar Radio Interface Compatible with Raspberry Pi 2/3/4 | Raspberry Pi Hosted Allstar Node | UHF Frequency Range 1W 420-450MHz/70cm | Amateur Radio Operator

Regular Price: US$161.99

Special Price US$134.99

Availability: In stock

Supplier: AURSINC

Category: Electronics Computers & Accessories Computer Components Single Board Computers

Qty:

Frequently bought together :

Price for all selected :

US$234.98

AURSINC SHARI (SA818 Ham Allstar Radio Interface) PiHat Allstar Node

SHARI (SA818 Ham Allstar Radio Interface) PiHat Allstar Node is a kit construction project that implements a Raspberry Pi4 hosted Allstar node using a NiceRF SA818 embedded UHF (420-450 MHz) or a VHF (144-148 MHz) radio module. The radio module and interface circuits are located on a custom Raspberry Pi Hat board. A complete Allstar node can be implemented with a SHARI PiHat kit, a Raspberry Pi 4 (with power supply and microSD card) and an Allstar image.

Features

Works with a Pi2/Pi3 or Pi4 (USB connector positions swapped)
Uses the Cmedia CM119B USB audio IC
Uses a NiceRF SA818 UHF or VHF embedded radio module
500 to 1000(default) milliwatts RF output power
Small, portable with self contained radio and antenna
Radio settings changed using a program running on the Raspberry Pi

Specification

Item Type: Radio Interface Module
UHF Frequency Range: 1W 420-450MHz/70cm
Compatible: Raspberry Pi 2/3/4
Material: Metal

Required Hardware

1. A fully assembled SHARI Pi3U, Pi3V, Pi4U or Pi4V.

2. A Raspberry Pi 2, Pi 3 or Pi4 . The Pi2 or Pi3 is normally used with the SHARI Pi3(U) ,while the Pi4 is normally used with the SHARI Pi4(U)

3. A case for the Raspberry Pi. A metal case is preferred but if you want to use a WiFi connection instead of a wired network connection then a plastic case may be required to obtain adequate range.

4. A micro SD card – 16GB or larger, Class 10 or better is recommended.

5. A power supply for the Pi-This should be a power supply intended for the version of the Raspberry Pi. These supplies typically provide 5.1 to 5.2 VDC to the Pi. Current requirements vary with version. Numerous problems with Allstar Nodes have been traced to inadequate power supplies.

Package List

SHARI PiHat Allstar Node x1
Antenna x1
USB Cable x1

SHARI Allstar Node Setup and Configuration Guide (In short version)

1. Create an Account with Allstar

2. Create a Server and Request a Node number

3. Software

4. Configuring Allstar

5. Configuring SimpleUSB-Tune-Menu for SHARI

6. Connecting and Configuring SHARI

7. Setting Receive and Transmit Voice Levels

8. Testing DTMF Decoding

9. Enabling the COS LED

[Feature 2] SHARI PiHat uses a single circuit board which contains installed surface mount (SMD) parts as well as 2 through-hole parts, a surface mount SMA connector and the SA818 (UHF) radio module; PiHatU also uses the Cmedia CM119B USB audio IC.NOTE: Support of SHARI is provided via the SHARI group at www.groups.io/g/shari. [Feature 1] Front panel LEDs indicate the status of SHARI-POWER (green), USB Audio CONNECTION STATUS (blinking green), COS (green) and PTT (red); SHARI PiHat uses 5 volts from the Pi, and the best place to measure it is from pin 8 (+5) to pin 9 (GND) of the SA818 module. [Power Supply] SA818 Ham Allstar Radio Interface is a power supply intended for the version of the Raspberry Pi. These supplies typically provide 5.1 to 5.2 VDC to the Pi. Current requirements vary with version. Numerous problems with Allstar Nodes have been traced to inadequate power supplies. [Allstar Node] SHARI PiHatU implements a Raspberry Pi hosted Allstar node using a NiceRF SA818 embedded UHF (420-450 MHz|70cm) radio module; In order to create an Allstar node, SHARI plugs into two USB jacks on a Raspberry Pi2/Pi3 or Pi4 for power, the Allstar interface and radio programming (a short M/F USB extender cable can be used if desired). [What Is It] Small, portable with self contained radio and antenna, SHARI(SA818 Ham Allstar Radio Interface) is designed for construction and uses in the amateur radio service, works with a Pi2/Pi3 or Pi4, SHARI RF output power is 500 to 1000(default) milliwatts.