ATmega32u4 Development Board 7 PWM Channel Development Module Microcontroller with USB Cable for Leonardo R3 Pro

BE SAFE

WE ONLY SOURCE

FROM OFFICIAL SUPPLIERS

From United States

To International

In 5-10 Days

US$19.99 Shipping Fees for any Order

GRAND SELECTION

Think of it and most probably we have it among our grand selection of products!

AMAZING PRICES

Get ready for the amazing and best Supps prices ever!

FIXED RATE DELIVERY

Get your order anywhere on this planet within 5-10 days with a fixed rate of $19.99 (no matter the size of your order)

+1 (844)-467 8777

PHONE:

+1 (844)-467 8777

ATmega32u4 Development Board 7 PWM Channel Development Module Microcontroller with USB Cable for Leonardo R3 Pro

Regular Price: US$35.99

Special Price US$29.99

Availability: In stock

Supplier: Oumefar

Category: Electronics Computers & Accessories Computer Components Single Board Computers

Qty:

Frequently bought together :

Price for all selected :

US$94.97

Error code and meaning:

Err1:battery voltage is higher than 15V

Err2:battery voltage is lower than set cutoff voltage

Err3:load discharge current is too big for battery or circuit inner resistance is too big

Err4:current is too big (current is more than 3.1A)

Err5:Improper use or burned tester because of incorrect connection (current sampling or control switch MOS is burned)

Secondary calibration operation:

Press and hold three buttons at the same time and power tester to enter calibration mode. First display calibration record times then enter formal calibration sampling program shows 0u0A; Connect input terminals positive and negative then press the "OK" button, display shows J10u; Connect standard 10.00V DC voltage to input positive and negative then press the "OK" button, display shows J2.0 A; Connect constant 2.0A DC current to output negative and input negative then press the "OK" button to complete the calibration.Tester will pre-check calibration data, if the calibration data is correct, it will show four calibration data in turns then exit; if pre-check of data is unreliable, it discards the data then exit.

Use a Demo

Instruction:

The measured battery should be charged in the first place.
Connect the battery to the input terminals correctly(positive to positive, negative to negative), reverse input may damage the circuit.Connect load to the output positive and negative, then power the meter with micro USB work power (do not use a desktop computer or laptop USB as power supply), it displays the battery voltage at this time.
Direct start test just need to press the "OK" button, then meter will automatically develop an appropriate cutoff voltage according to the battery fully charged voltage, then begin testing after display flashing 3 times.If need manual setting up for cutoff voltage, you can press "+" or "-" button when ti shows battery voltage. The cutoff voltage is displayed with a initial "P", and the resolution is 0.1 V, press "OK" to start testing after setting.
The testing data will be displayed in turns among discharge capacity (Ah), real-time discharge current (A) and battery voltage (V). When the battery voltage reaches set cutoff voltage, tester cut off the load control switch, and displays capacity (Ah) and fast flashing indicator light. The capacity now displayed is the actual discharge capacity of the battery. Press the "OK" button to stop flashing, and press the "OK" button again to reset tester for next battery testing.

Package list:

1 * Battery Capacity Meter
2 * Resistors (5W, 7.5R)
1 set * Fasteners

Please select the load resistance appropriately, and ensure that the current cannot exceed 3A at any time.
Please use the mobile phone charging head for power supply, do not use the power bank

Specification:

Power Source Voltage: DC4.5-6V (micro USB)

Working Current: =70mA

Discharge Voltage: 1.00V-15.00V, resolution 0.01V

Cutoff Voltage Range: 0.5-11.0V

Supported Current: =3.000A, resolution 0.001A

Voltage Test Error: <1%+0.02V

Current Test Error: <1.2%+-0.002A

Battery Capacity Range: 9999Ah (1Ah=1000mAh, the decimal point can move when the number is large, e.g. it displays X.XXX when lower than 10Ah, and displays XX.XX when higher than 10Ah... )

Weight: 27g / 1oz (approx.)

Note:

The resistor load will heat up severely during discharge process, please be careful.
In order to improve the voltage measurement accuracy, this circuit is specially designed with a DC bias, and will display a small voltage when not connecting terminal blocks to anything, which does not affect the actual measurement. If you connect input terminals together(0V), it will display 0.

Estimating method for collocation resistance:

According to Ohm's law, to estimate the resistance value = divide battery voltage by expected discharge current; resistor power choice is more than two times of result that the battery voltage is multiplied by expected discharge current. It is important to note the voltage is higher when battery is fully charged, and to ensure that the current can not be more than 3.0A in the case of full charged battery voltage.For example, if need to use 2A to test 12V battery, then the resistor should be 6O 50 W. New 12V battery fully charged voltage is about 13.5V, which is corresponding to the maximum current 13.5/6=2.25A (less than 3A), so it can be used.In addition if you use the lamp bulb to test, then the current can only be less than half (1.5 A) because the light bulb cold resistance is low, the impact current is very big, too big current may burn circuit directly.