115 dB Srong Loud Alarm Volume

3-Level Adjustable Volume and Sensitivity

Motion Sensor and Vibration Detection

Type-C Rechargeable (400mAh Li-ion Ploymer Battery)

Long-Distance Remote Control

Meet the Needs of Use in Different Situations

IPX5 Waterproof

Wireless Remote Control and Can Be Used as a Horn

Well Made and Easy to Use and Instal

(1) Arming & Disa rming

Arming: Short press the remote control lock button will sound "Do-Re- Mi", at this time

the main unit has entered the arming state. 3 seconds later to hear "DI", during this period touch the

main unit will issue a "di-di ". If you continue to touch the mainframe again, the alarm will be .

"biu- biu-biu" for 30 seconds. 30 seconds after touching it again, the alarm will continue.

Disarming: In the arrming state, short press the rermote control urlock button, the main

unit will sound "mi-re-do", at this time, the main unit has been disarmed.

(2) Alarm:

In disarming mode, short press lightning button, the main unit will keep alarming

biu-biu-biu". You can short press unlock button to exit.

(3) Electric Bell:

In disarming mode, short press remote bell button, the main unit will sound the

previously set electrie bell. Short press short ring. long press long ring.

Quickly Determine Vehicle Location

Press the instant electric horn or panic alarm button on the remote

Easily find your vehecle by the super loud prelong beep beep or siren sound

(4) Personalized Setting

1.Alarm vibration sensitivity stting: Press and hold the remote control button until the remote control LED 1ights up again, and the alarm will have a "Bi" sound. At this time and then press the remote control button, each time you press, the vibration sensitivity switch level. Sensitivity has 3 levels adjustable; high - medium - low. The corresponding sound is "Bi BiBi (high)", "BiBi (medium)" "Bi (low)", after stting, press the remote control button to exit the setting.

2. Alarm has 3 levels of volume can be set: high - medium - low. Press and hold the remote control button and do not release your hand until the remote control LED lights up again, while the alarm will have a "Bi" prompt, at this time in the remote control button, each press, switch the volume once, each switch to play the coresponding volume of"Bi" sound. When the setting is finished, press the remote control [b] button to exit the setting.

3.Ringtone S etting: When jtis not in the armed state, you can set 5 kinds of ringtones. Press the alarm will have a "Bi" sound. At this time in the remote control button, each time you press, the bell switch once, and play the corresponding ringtone. When the setting is complete, press the remote control button to exit the setting. The five ringtones are "horn sound 1","horn sound 2", "horn sound3", "bird sound" and "di-di sound".

(1) 2 Hours fully charged.

(2) When charging, the power indicator 1, 2, 3 in turn gradually increase until 3 bars are always on fora fiull charge.

(3) When the power is low, the power indicator 3, 2, 1 in order to reduce to 1 bar of power,please charge.

(4) When charging. it is recommended to use the power bank to charge directly or the main,unit screw loosened and removed before charging.

Installation of Remote Control

(1) The remote' bracket is fixed with a tie in a position that is easy to touch with the left

and right thumbs.

(2) Place the remote.

(3) Press and hold the bottom snap position of the bracket to remove the remote.

Installation of Bike Alarm

(1) Choose any position on the bike where it can be fixed.

(2) Secure and tie down the main unit and cut off the excess tie.

(3) Insert the main unit into the fixing bracket and tighten the screw.

(4) The main unit can be removed by loosening the screw in an anti-clockwise direction.